cncvicut

Analysis of the reasons for the weakening of the  Laser Welding Machine  provided by the  China Laser Marking Machine Manufacturer : 1. Main light path laser offset processing method: adjust the main light path full-reverse and semi-reflex film, use paper to check and round the spot 2, focusing lens damage or pollution treatment: replace or clean the focus lens and protective lens. 3. The laser does not output from the center of the copper nozzle below the focusing head. The method is to adjust the 45-degree reflection diaphragm to make the laser output from the center of the nozzle. 4, the laser cavity diaphragm damage or pollution treatment: replace or clean the resonant cavity reflective diaphragm. 5, the shutter does not completely open the treatment method: check and add lubricant on the shutter connection, so that the connector can be mechanically smooth 6. The service life of the xenon lamp has reached the treatment method: check and clean the old lamp or replace it

When the unit is not working, the  Table Type Fiber Laser Marking Machine  and computer power should be turned off. When the machine is not working, cover the field lens lens to prevent dust from contaminating the optical lens. When the machine is working, the circuit is in a high voltage state. If it is not a professional  China Laser Marking Machine Manufacturer , do not overhaul it during startup to avoid electric shock. If there is any malfunction of this unit, the power should be cut off immediately. When the equipment is used for a long time, the dust in the air will be adsorbed on the lower end surface of the focusing mirror. The lighter will reduce the power of the laser and affect the marking effect; the heavy one will cause the optical lens to absorb heat and overheat and burst. When the marking effect is not good, carefully check the surface of the focusing mirror for contamination. If the surface of the focusing mirror is contaminated, the focusing mirror should

We should pay attention to safety issues when installing the  Contour Cutting CNC Router . Here are some installation precautions  CNC Router Supplier  will tell you, we hope to help you. 1. Don`t set the power socket in or around the moist area or area. 2. Machine Operator needs to be trained only before operate the machine. Individual and Gear safety must be more focused. 3. Stabilizer is required if the voltage is instable or there's high-power gear nearby. 4. Ground cable connection have to be made. It isn't permitted to connect or disconnect signal cable with power connected. 5.Please utilize glove, eyeshield and earplug when working on the machine. 6. Please tight the screws properly but do not too much if screws slipped. 7. Please clamp the cnc tools with fully tightness and replace the dull tools timely. Overloading to the spindle and poor working performance can caused because of blunt tools. 8. Keep your fingers far away from your working place. 9.

The maintenance of machine tools is very important to the life of machine tools. The following  Digital Flatbed Cutter Manufacturer  will provide you with some knowledge of machine tools maintenance. First, daily maintenance 1. Check the lubricant level to ensure the lubrication of the  Metal Mold CNC Milling Machine . 2. Check if the coolant in the coolant tank is sufficient and not enough to add it in time. 3. Check the oil level of the pneumatic triple joint, which is about 2/3 of the height of the entire tubing. The water in the pneumatic triple-link filter tank is discharged by the drain switch every day. 4. Check if the air blowing in the taper hole of the spindle is normal. Wipe the inner cone hole with a clean cotton cloth and spray light oil. 5. Clean the tool pocket and tool, especially the claws. 6. Clean the exposed limit switches and bumps. 7. Remove cutting and oil stains on the workbench, machine tool, and three-axis telescopic cover. 8. Check all the

A hardware product must be marked on the factory before shipment: product name, bar code, product serial number, anti-counterfeit identification, instructions, production date and other key information, in order to facilitate factory management and market supervision and management, and to complete these tasks, inevitably To use  Laser Marking Machine , especially in high-volume production lines, laser marking machines with high processing speed and high mark forming rate should be used. China Label Cutter Machine Supplier  Supplies laser marking machine is a modern leading precision machining method. Compared with the traditional printing, manual engraving, mechanical engraving, EDM machining, grinding tools, etc., laser marking machine has many advantages: In the processing, laser The marking machine can quickly complete surface burr removal, character and logo marks, anti-counterfeiting marks, product numbers and bar code marks. In routine maintenance and use, the laser marking m

Cutting material is one of the important reasons that influence the cutting speed of  Digital Flatbed Cutter . Besides, it is also affected by the following factors, let  Digital Flatbed Cutter Manufacturer  tell you : 1, the cutting speed is affected by the cutting material Acrylic cutting machine is basically the processing of our plate is common, such as various KT board, Chevron board, honeycomb board, car stickers, adhesive, frame paper, gray paper, corrugated paper, EPE foam, PVC board, acrylic Plate, thick foam and so on. The cutting speed of the acrylic cutting machine has a great relationship with the nature of the cutting material. 2, the thickness of the cutting material affects the cutting speed In general, the thinner the cutting material is, the easier it is to cut and the faster the speed is. The cutting speed of the thin plate is faster than that of the thick plate. Therefore, the thickness of the cutting material affects the cutting speed. 3, whether the use

作为  Digital Flatbed Cutter制造商 ，我们会告诉您使用 Digital Flatbed Cutter 应该注意的事项     1）移动工作台或主轴时，需要根据工件的距离正确选择移动速度，并在移动过快时防止碰撞。 2）在编程过程中，应根据实际情况确定正确的加工工艺和加工路线，并应提前消除或切断加工位置不足或切削刃强度不足造成的工件。 3）在线切割之前，需要确认程序和补偿量是否正确。 4）检查线张力是否足够。 切割锥度时，张力应减少到通常的一半。 5）检查电极丝的进给速率是否正确。 6）根据工件的实际情况选择开式加工或密闭加工，在避免干涉的前提下尽量减小喷嘴与工件之间的距离。 对于密切处理，喷嘴和工件之间的距离通常为0.05至0.1mm。 7）检查射流的选择是否合理，使用高压射流进行粗加工，并使用低压射流进行精细加工。 8）切割时，应注意观察和判断加工稳定性，如果发现不好，及时调整。 9）在加工过程中，经常检查和监督切割条件，发现问题立即得到解决。